144" on 04 Viper S or 00 SRX

dewieiii

dewieiii

Member
Joined
Mar 6, 2007
Messages
59
Age
52
Location
ON CAN
:o| Both sleds are completely stock and have approx. 7,000 km. The Viper S is electric start and reverse while the SRX is plain jane. The rear skid I'm looking to install is a 144" Viper Mountain Skid and 1.3" Cobera track. The question is witch sled would be better to change over. I don't do a lot of trail riding, the reason I'm looking to extend the tack, I ride 1/2 the time in and out of fishing towing a portable ice hut and the other 1/2 the time wanting to bang the ditches, play in the hills and powder. Oh and not to mention I still like the 100 mph top end. I know it is a little late to start the project this year but I keep putting it off not knowing which sled to put FOR SALE. Also my other question is while I have the chain case open should I be looking to change any of the gearing since going from 121" to 144". I'm really looking for anyone to pitch in their 2 cents.

:2strokes:
 
If it were me I'd do it on the Viper. Mainly because it has a long travel front to match the rear. I'd get it geared to match final ratio of a mountain Viper. You'll have to do some math though as mountain Viper had 8 tooth drivers I believe so if you keep the 9 tooth you'll need different gears to get the same end ratio.
 
Thanks, I was looking at going to a smaller drive sprocket (8 tooth) on either machine in order to have the clearance for the deeper lugs to ensure I kept the track out of the heat exchangers.
 
I did a 144 viper and it came out awesome. Same sled as yours. I didn't change drivers or gearing and never had any issues on or off trail. Do a search for "pair of Vipers go 144". You can see e Carly what you will have.
 
I have 1 of each both with aftermarket ekholm tunnels with drop and roll chain cases and 9 tooth extrovert drivers, srx is a 141 and viper is 144,I just bought and rebuilt srx last year and barely have 10 miles on it, viper just bought last month and rebuilding motor, i could tell a huge difference over my 121 99 srx, seems like they lift out of the snow better instead of digging a trench on takeoff
 
I would go for the Viper also, but then again I'm biased :roll:. But I agree with Staggs. You would get a better suspension for the powder riding. If you look at the specs for the clutching and gearing in the Tech Section, there's a difference between the two in all drive line aspects. If I were doing this project, I would leave everything as is, and decide later about the gearing / clutching.

I consider my mountain vipers great crossover sleds.
 
Well thanks for confirming folks, I was leaning to the Viper too. I did look over "super1c's" extension project and a couple of others and gotta say they really do look good once complete. I'm not going to be using extensions but rather installing a 144" viper mountain skid into my tunnel and know a great fab shop that will be doing my tunnel for me. I do have a couple more questions though, my 04' Viper S came with a rear heat exchanger. I viewed a couple of builds on the site and it sounded as though guys were buying them and or modifying SRX rear coolers I'm sure mine came with it as I bought the sled a couple of years old (in 2006) and the guy only had 200km on it and I've had it ever since. I think I'm going to stick with my 9 tooth drivers as suggested since the cobra track I have is the 1.36". The reason being that I got it from a friend of mine who after just a couple hundred miles on his new sled totaled it and I got a super deal on the track. Like I mentioned before this sled is complete stock with NO modifications at all and original factory clutch that I've never played with just cleaned, am I best to leave everything alone or should I change anything in the chain case while I have it apart. I can always make small adjustments to the clutch as far as different spring and or spring settings but don't really know a lot about that. Some of the posts I've read about clutches are chinese to me and talk about heel klickers and weights to which I haven't the slightest clue. I know enough to keep them clean and to adjust the defection so that the belt sits up about 1/8" to 3/16" but that's about it. If anyone can spell it out for me in lame mans terms that would be sweet.
 
You must log in or register to reply here.


Back
Top