all throttle no bottle
Member
I HAVE A 2000 SXR 700 WITH BENDER TRIPLE PIPES . H/C CLUTCH KIT . 1 1/4 RIPSAW TRACK WITH 96 STUDS . THE HEAD HAS BEEN SHAVED 20 THOUSANDS . REED NOTCH . 45/39 HELIX GREEN SECONDARY SPRING . 24/38 GEARS WITH 8 TOOTH DRIVERS . I WAS AT HOUGHTON LAKE THIS WEEKEND AND A FREIND WAS RADARING AND I ONLY GOT 86MPH . THAT SUCKS IF YOU ASK ME. I RACED 2 F7S 1 ZR 900 AND A MXZ 800 ALSO A VIPER I CAN GET ALL OF THEM OUT OF THE HOLE ALL THE WAY TO ABOUT 70 THEN THEY GO BY ME . IT SEEMS THAT I HAVE GREAT LOW END JUST NO GOOD MID TO TOP END. WHAT CAN I DO THANKS . 

Last edited:
Are you getting the right weight transfer on this, do you have no transfer. This happen to me when I bought mine, the guy set it with all ski pressure and no transfer
all throttle no bottle
Member
No Its Got GREAT Transfer. Its GetS Out Of The Hole GREAT Just No Mid To Top End.
Last edited:
what are your rpm's? are they pullin up to your peak? how are your sec. buttons?
T.S.U.Filmz
Member
did you have a pull through on one of the Power Valves?
Yama49601
Member
He doesn't have power valves. Unless I missed something.
did you clip the track when you installed it or did you remove your heat exchangers. 1 1/4 camos dont fit in a pro action without one of these being done.
all throttle no bottle
Member
Track
I Did Not Clip Track Or Remove Heat Exchanger . I Have 8 Tooth Drivers. ALSO WHEN I AM TOPPED OUT IT IS AT 9000 RPM
I Did Not Clip Track Or Remove Heat Exchanger . I Have 8 Tooth Drivers. ALSO WHEN I AM TOPPED OUT IT IS AT 9000 RPM
aren't benders supposed to be at 8500? If so, you are out of your power band,need to get those r's downall throttle no bottle said:I Did Not Clip Track Or Remove Heat Exchanger . I Have 8 Tooth Drivers. ALSO WHEN I AM TOPPED OUT IT IS AT 9000 RPM
bufalobob
Member
yammy is correct. put weight in the front clutch - 8500 rpm.
in perfect conditions you are geared for about 108 mph on a long pull - but not with the ripsaw on. hacksaw or predator - 1" - would have been a better choice for top end. your quicker out of the hole because of the ripsaw & slower on top for the same reason.
bob
in perfect conditions you are geared for about 108 mph on a long pull - but not with the ripsaw on. hacksaw or predator - 1" - would have been a better choice for top end. your quicker out of the hole because of the ripsaw & slower on top for the same reason.
bob
all throttle no bottle
Member
I Was Told By Turk The Rpm Should Be At 9000 - 9100 With Beder Pipes . Even With The Ripsaw Track I Would Think I Sould Get 100 Mph Out Of It .
bufalobob
Member
8500 rpm.
you've also got 8 tooth drivers which is adding to the problem. makes for a tighter track turning radius. put the 9 tooth drivers back in. the track will clear.
bob
you've also got 8 tooth drivers which is adding to the problem. makes for a tighter track turning radius. put the 9 tooth drivers back in. the track will clear.
bob
all throttle no bottle
Member
I Have Studs
bufalobob
Member
bring your rpm's down to 8500 & go out & run it. if still not happy trim the ripsaw down to 1" & put the 9 tooths back in with 1.075 studs. will then mph about the same as a 1" predator.
bob
bob
all throttle no bottle
Member
Why Would I Cut A $350 Truck Down To 1 Inch I Wanted A 1 1/4 Track For More Traction . I Am Not Looking To Get 150 Mph Out Of The Thing I Just Think 86 Mph Sucks .
You Cut the track because it rubs the heat exchanger...therefor SLOWING you down. Just cut notches in the track where it come in contact with the exchanger. If your track is to tight this also will hurt your top end.
he is saying put the 9 tooth drivers back in and cut notches in the track where they come in contact with the protectors, or you can just let them wear grooves. Did you gear it for 8tooth drivers? Benders should be around 8500. I've got SLP's and I can just about bury the dreamometer on ice. 86mph somethings not right
97sx700
New member
i have bender pipes on mine and i only run 8500 rpms wot. on the lake i run around 107 according to the skidoo 800r digital speedo says
tedgoesfast
New member
i have a one inch track on mine with tranfer rod it hooks good on trails and mine will go oner 100 mph geared 22/40
all throttle no bottle
Member
I Thought You Had To Use The 8 Tooth Drivers For The Studs . So Puting The 9 Tooth Drive In And Cuting The Track Will Not Work Right .